* Initial version
*
* $DESCRIPTION$
+ * Set up of basic exceptions and interrupts. These interrupts
+ * don't do much, except for halting the system.
+ * ivt_set_gate(interrupt nr, function, priority) can be used
+ * later to define more appropriate handling. See timer (timer.c)
+ * or serial or (uart.c) handling for non-trivial examples.
+ *
+ * The actual code is not much, but there are a lot of details
+ * to consider. Besides that, in case more control is desired over
+ * entering and exiting interrupts (what is pushed on the stack)
+ * A so-called naked function can be used. See below for more
+ * details.
*
+ *
* */
#include <stdbool.h>
#include <stddef.h>
#include <stdint.h>
-#include <stm32.h>
-#include <mmap.h>
+
+#include <sys/robsys.h>
+#include <sys/mmap.h>
+
+#include <lib/stdio.h>
+#include <lib/string.h>
+#include <lib/regfunc.h>
+#include <lib/tinyprintf.h>
/*
* These values are pushed on the stack just before
* gives me a little bit more control over the caller
*
* The following register are pushed to the stack
- * in reverse order
+ * in reverse order:
*
* */
struct interrupt_frame {
/*
* Vector table, each entry contains an interrupt
- * service routine:
- *
+ * service routine:
* interrupt vector 1-15: processor exceptions
* interrupt vector 16-92: irq0 - irq ..
+ * Vector table needs to be aligned in memory.
* */
+uint32_t __attribute__((aligned(0x100))) ivt[92];
-uint32_t ivt[92];
+/* Each message corresponds to each and every exception. */
+char * exception_message(uint8_t intnr) {
-/* each message corresponds to each and every exception.
- * We get the correct message by accessing
- * exception_message[interrupt_number]
- * exception_message[0] is not used (=MSP)*/
+char * messages[] = {
+ "--",
+ "RESET",
+ "NMI",
+ "HARD FAULT",
+ "MEMMANAGE FAULT",
+ "BUS FAULT",
+ "USAGE FAULT",
+ "RESERVED",
+ "SVC",
+ "DEBUG MONITOR",
+ "RESERVED",
+ "RESERVED",
+ "RESERVED",
+ "RESERVED",
+ "PENDSV",
+ "SYSTICK",
+ "IRQ1",
+ "IRQ2",
+ "IRQ3",
+ "IRQ4",
+ // add more if needed
+};
-char * exception_message(uint8_t intnr) {
+if (intnr < 20) // TODO: strlen
+ return messages[intnr];
- char * messages[] = {
- "--",
- "RESET",
- "NMI",
- "HARD FAULT",
- "MEMMANAGE FAULT",
- "BUS FAULT",
- "USAGE FAULT",
- "RESERVED",
- "SVC",
- "DEBUG MONITOR",
- "RESERVED",
- "RESERVED",
- "RESERVED",
- "RESERVED",
- "PENDSV",
- "SYSTICK",
- "IRQ1",
- "IRQ2",
- "IRQ3",
- "IRQ4",
- // add more if needed
- };
-
- if (intnr < 20) // TODO: strlen
- return messages[intnr];
-
- return NULL;
+return "UNKNOWN";
}
void ivt_set_gate(unsigned char num, void * isr(), short pri) {
ivt[num] = (uint32_t) isr;
- *NVIC_ISER0 = (1 << ((uint32_t)(num) & 0x1F));
- /* Priorities */
+// if (num <= 32)
+// *NVIC_ISER0 = (1 << ((uint32_t)(num) & 0x1F));
+ /* TODO: Priorities */
}
-/* Dummy interrupt */
-// __attribute__ ((interrupt))
-void * dummy_isr(/* struct interrupt_frame * frame */) {
+/* Dummy interrupt: comment out the comment to use a naked
+ * function */
+
+__attribute__ ((interrupt))
+void * dummy_isr( struct interrupt_frame * frame ) {
uint8_t nr = *SCB_VTOR_ST & 0xFF;
+ printf("EXCEPTION: %s\n", exception_message(nr));
+ printf("STACK TRACE:\n");
+ printf("R0:%p\n",frame->r0);
+ printf("R1:%p\n",frame->r1);
+ printf("R2:%p\n",frame->r2);
+ printf("R3:%p\n",frame->r3);
+ printf("R12:%p\n",frame->r12);
+ printf("LR:%p\n",frame->lr);
+ printf("PC:%p\n",frame->pc);
+ printf("PSR:%p\n",frame->psr);
- uart_puts("EXCEPTION: ");
- uart_puts(exception_message(nr));
- uart_puts("\nSYSTEM HALTED\n");
-
- for(;;);
+ //for(;;);
}
/* Initialize interrupt vector */
void ivt_init() {
- /* clear entiry IVT, in SRAM location for SRAM + .data (in .bss section) */
+ /* clear entire IVT location in memory */
memset(&ivt, 0, (sizeof(uint32_t) * 92));
- // stack top is loaded from the first entry table on boot/reset
- // don't need to relocate or init this here
+ /* The reset, NMI and hardfault handlers are originally
+ * defined in the assembly start up and can be
+ * reused or overwritten.
+ * */
extern void * reset, * nmi, * hardfault;
+ // set dummy handlers
for (int i = 1; i <= 64 ; i++) {
ivt_set_gate(i, dummy_isr, 0);
}
-
- /* the vector table starts at 0x0. Since the address 0x0 point to
- * bootcode, it is on ROM or FLASH. The vector table can be
+ /* The vector table is intially at 0x0. The vector table can be
* relocated to other memory locations. We can do this by setting
* a register in the NVIC called the vector table offset register */
- //*SCB_VTOR = (volatile uint32_t) &ivt;
- regw_u32(SCB_VTOR, (uint32_t) &ivt, 0, 0x01);
+ rwrite(SCB_VTOR, (uint32_t) &ivt);
}