#include <stm32.h>
#include <mmap.h>
-/* TIMER, TODO: move to timer.c */
-
-
-
-/* Interrupt vector can contain 16 exceptions and up to 256 interrupts
- * In this code we use 16 exceptions and 36 interrupts
- * (note: this should be aligned to the vector table size)
- * Offsets of each entry is: 0x0, 0x80, 0x100, 0x180 .. */
+/*
+ * These values are pushed on the stack just before
+ * entering the ISR. Normally, this would require
+ * assembly or inline assembly code. I use a so-called
+ * 'naked function' __attribute__ ((interrupt)) which
+ * gives me a little bit more control over the caller
+ *
+ * The following register are pushed to the stack
+ * in reverse order
+ *
+ * */
+struct interrupt_frame {
+
+ uint32_t r0; // N-32
+ uint32_t r1;
+ uint32_t r2;
+ uint32_t r3;
+ uint32_t r12;
+ uint32_t lr;
+ uint32_t pc;
+ uint32_t psr; // N-4
+};
+
+/*
+ * Vector table, each entry contains an interrupt
+ * service routine:
+ *
+ * interrupt vector 1-15: processor exceptions
+ * interrupt vector 16-92: irq0 - irq ..
+ * */
-/* interrupt vector 1-15: processor exceptions
- * interrupt vector 16-43: irq0 - irq .. */
-uint32_t ivt[43];
+uint32_t ivt[92];
+
+/* each message corresponds to each and every exception.
+ * We get the correct message by accessing
+ * exception_message[interrupt_number]
+ * exception_message[0] is not used (=MSP)*/
+
+char * exception_message(uint8_t intnr) {
+
+ char * messages[] = {
+ "--",
+ "RESET",
+ "NMI",
+ "HARD FAULT",
+ "MEMMANAGE FAULT",
+ "BUS FAULT",
+ "USAGE FAULT",
+ "RESERVED",
+ "SVC",
+ "DEBUG MONITOR",
+ "RESERVED",
+ "RESERVED",
+ "RESERVED",
+ "RESERVED",
+ "PENDSV",
+ "SYSTICK",
+ "IRQ1",
+ "IRQ2",
+ "IRQ3",
+ "IRQ4",
+ // add more if needed
+ };
+
+ if (intnr < 20) // TODO: strlen
+ return messages[intnr];
+
+ return NULL;
+}
-/* * base is location of interrupt service request
- * */
void ivt_set_gate(unsigned char num, void * isr(), short pri) {
ivt[num] = (uint32_t) isr;
- // TODO priority
+ *NVIC_ISER0 = (1 << ((uint32_t)(num) & 0x1F));
+ /* Priorities */
}
-// test Interrupt service routine
-void * test_ISR() {
- uart_puts("PING!");
+
+/* Dummy interrupt */
+__attribute__ ((interrupt))
+void * dummy_isr(struct interrupt_frame * frame) {
+
+ uint8_t nr = *SCB_VTOR_ST & 0xFF;
+
+ uart_puts("EXCEPTION: ");
+ uart_puts(exception_message(nr));
+ uart_puts("\nSYSTEM HALTED\n");
+
+ for(;;);
}
/* Initialize interrupt vector */
-
void ivt_init() {
/* clear entiry IVT, in SRAM location for SRAM + .data (in .bss section) */
- memset(&ivt, 0, (sizeof(uint32_t) * 44));
+ memset(&ivt, 0, (sizeof(uint32_t) * 92));
// stack top is loaded from the first entry table on boot/reset
// don't need to relocate or init this here
-
- // copy old vectors
extern void * reset, * nmi, * hardfault;
- //extern uint32_t reset, nmi, hardfault;
- //ivt[1] = &reset;
- //ivt[2] = &nmi;
- //ivt[3] = &hardfault;
-
- ivt_set_gate(1, test_ISR, 0);
- ivt_set_gate(2, test_ISR, 0);
- ivt_set_gate(3, test_ISR, 0);
- ivt_set_gate(15, test_ISR ,0);
-
- // enable all interrupts
-
- *SYSCTRL_RCGC1 = *SYSCTRL_RCGC1 | 0x00010000;
- // TODO systimer
- // ivt[15]
- *NVIC_EN0 = *NVIC_EN0 | 0x00008003;
-// *NVIC_EN1 = (volatile uint32_t) 0xFFFFFFFF; // TODO not all registers
-
- // priority levels are 0 by default (only executable by kernel)
-
- /* disable all interrupts
- * MOV R0, #1 ; disable all
- * MSR PRIMASK, R0
- * MOV R0, #0 ; allow all
- * MSR PRIMASK, R0 */
-
-
-
- /* relocate the vector table to (S)RAM
- * vector table starts at 0x0. since the address 0x0 point to bootcode, it is on ROM or FLASH.
- * the value cannot be changed during runtime. however, the vector table can be
- * relocated to other memory locations in the code or RAM later on
- *
- * we can do this by setting a register in the NVIC called
- * the vector table offset register (address 0xE000ED08). */
+ for (int i = 1; i <= 6 ; i++) {
+ ivt_set_gate(i, dummy_isr, 0);
+ }
+ /* the vector table starts at 0x0. Since the address 0x0 point to
+ * bootcode, it is on ROM or FLASH. The vector table can be
+ * relocated to other memory locations. We can do this by setting
+ * a register in the NVIC called the vector table offset register */
- *NVIC_VECTTBL = (volatile unsigned long) &ivt;
+ //*SCB_VTOR = (volatile uint32_t) &ivt;
+ regw_u32(SCB_VTOR, (uint32_t) &ivt, 0, 0x01);
}